In this article, you will be learning how to make your own electric skateboard step by step.
If you have ever considered building an electric skateboard yourself that allows you to travel around the city then, this tutorial will be helpful to you.
You may think that building an electric skateboard is very complicated, but the truth is that if you follow these steps, you will see how not only you are capable but that you are going to have fun riding it with your own hands and it will cost you much lower than what you would find in the market.
Benefits of electric skateboard
- It is a fast, agile, and non-polluting transport vehicle.
- It is enjoyable if you like snowboarding, surfing, and miss practicing it all year with an electric skateboard you can do it
How to build an electric skateboard
First of all, you gather all the materials.
Materials to create the skateboard
So you must get first of all the following materials:
- A good adhesive
- Baltic birch plywood
- Sandpaper both thin and thick
- A drill
- Paper and a pencil to create your drawing on the table.
- Table construction
Once this is done, you must cut the plywood into two pieces of a quarter of plywood of a size of 30 centimeters by 150 centimeters.
Once you have done this, you must get creative and make the drawing of your table so that it is customized as you like. So, first, outline what your table will be, then take the paper and pencil and make a straight line near one end, that will be the center of your future longboard.
After this, you must draw half of the board against that line. It is essential that if it is the first table that you make, try to draw it in the simplest way possible, that is, make a curve that is not very pronounced, but that is wide of approximately one-third of the nose.
Even so, you can do it as you like according to your imagination and creativity.
Once you have drawn, place it on the wood, and take one of the pieces of plywood that you have purchased, this will make the bottom of the skateboard.
After this, keep your drawing in place, copy the mold of the edges that you had previously made, then turn it over and repeat the process on the other side, so your design will already be on the wooden board, then remove the mold from Plywood, and you will have your silhouette.
After this, you must drill and make an essential number of holes in the outer area of your drawing, that is, around the outside on the wood.
The holes should be a single inch from the lines. These holes will then serve to staple both pieces.
Then we must get our skateboard to take shape. For this, you must accept the two pieces of plywood and stack them; that way, the created pattern will be on top, and the part will be down.
After this, place the pieces so that each edge is supported by something, and the medium can hang freely. Then you must curl up in the middle so that it will level when you stand on it. Once this is done, you must place each weight on it until you get the desired result.
If what you want is to obtain even better results, we recommend that you make a small curvature and then put each weight on them, and in the broadest part of the skateboard. You should leave it this way until the curve of the table is optimally seated.
Once we have achieved this, you must glue each piece of wood. For this, you must mix the adhesive with a brush on the inner faces of each piece of wood. Mix the resin and, using a brush, spread the right amount of glue on the inner faces of both parts of the wood.
Doing this, you must be very careful. This is where we will pick up the point of the holes that we previously drilled since the adhesive will come out through each hole and the edge of the wood.
After this, put a screw that goes through a hole that is near the nose of the longboard. Then place each weight on it again. If you like how the curvature is, then, introduce the screws in the rest of the holes.
Once this is done, recheck the curvature to make sure everything is correct, and wait for the adhesive to act.
Then unscrew the screws, cut the board over the lines (do not forget that it will be the part under your longboard), sand the board to leave it very smooth and without chips, then varnish it and wait for it to dry.
After the varnish works, sand again, this time with fine sandpaper. After this, be creative and make your design with paint. And then it gives the final touch with a new layer of varnish.
Finally, if you want to get a more relaxed finish, use insulating tape to cover the board.
Assembly of the electrical system
Next, we will explain the electrical part of your longboard. Take note, we started
You would need a longboard board, and we already have this point because we did it in previous steps.
Now you will need a battery and an electric motor, drill, more nuts and bolts, and tweezers.
Take the table we had previously made and your new engine, if it is 36 volts or at least 24, it is vital that you know that the 24 will heat up more and have a shorter life.
Once the engine is selected, it is essential that you replace the rear hub of the skateboard with a cogwheel on the axle and also replace it with a solid axle. Once this is done, you must mount under the table and fasten the engine with screws so that the transmission and the belt can be adjusted to the cogwheel that we had previously replaced.
Remember that the belt is fixed on the pulley. Next, the other end of the belt must be placed on the lift that is attached to the wheels, ensuring that the regulators and the motors coincide with both tension and power.
You must remember the electric batteries are 12 volts, so if you want a 24-volt motor, you will need two, and if you want something more powerful, that is 36 volts; you will need three.
Once you have all this, you have to adjust all the joints, start the engine and you can start skating and enjoy your electric skateboard.
I believe this article has been able to help you understand how to make your own electric skateboard
You’ll Love to Know: Benefits of Skateboard Wheels